在線離線一體TOC分析儀   二氧化碳傳感器

儀器上安裝有兩個二氧化碳傳感器，由電導率傳感器和溫度傳感器組成。電導率測量采用雙精度技術，可以實現自動校準和溫度補償。TIC傳感器用于檢測未經氧化的水樣中二氧化碳濃度，同時檢測水樣的電導率值；TC傳感器用于檢測水樣本身含有的二氧化碳和水樣中有機物經分解后產生的二氧化碳濃度的總和。

在線離線一體TOC分析儀   分流器

水樣進入儀器后分成相同流量的兩路，其中一路通過延遲線圈進入二氧化碳傳感器，檢測TIC，另一路通過氧化反應器利用紫外燈（UV燈）加二氧化鈦薄膜光催化氧化作用將有機物分解為二氧化碳，進入二氧化碳傳感器檢測TC。總有機碳可通過這個差值計算得到：TOC = TC–TIC。

更換蠕動泵管

蠕動泵管在長期運行后會有磨損和老化現象，所以必須定期更換。

更換泵管的操作步驟如下：

○1 關閉主電源開關，拔去電源線。

○2 按下泵頭下部的金屬?gòu)椘瑥棾鰞蓚€(gè)塑料卡片。

○3 從甭管的接頭處拆下舊的蠕動甭管，取下套在甭管上的抱箍，將抱箍套在新

的蠕動泵管上，然后將新的甭管裝入儀器的接頭上，要注意抱箍的位置及方向。

○4 將甭管嵌入兩個塑料卡片，然后向下壓入卡位。按下時一定要注意甭管是否

入槽。

○5 調整卡片上的流速調節鍵，要注意調整的原則是：管路出液口的液體順暢自

然，無回流。條件允許的話，請使用高精度的量筒對出液速度進行測量，使液體的流

速與儀器的流速設置值相對應。

更換以上部件時存在問題可聯系儀器廠家解決。

保存歷史記錄

歷史記錄的保存對象包括：在線分析結果和離線分析結果。

分析儀有兩種存儲模式，一種是自動存儲；另一種是手動存儲。當選擇自動

存儲時，每次測試結束后，儀器會自動保存本次的測試結果。當選擇手動存儲時，每

次開始測試的時候，儀器都會有提示信息，詢問用戶是否要保存數據。如果要保存測

試結果則按“確定”鍵保存，如果不保存，則按“取消”鍵放棄保存。

主要特征:

★高精度、高靈敏度，操作簡單。

★人性化操作界面，有一鍵運行功能，自動管路清洗功能。

★高性能CPU，觸摸屏設計，超大640*480點陣真彩顯示器。

★不用拆開機箱更換UV燈和泵管。

★檢測上限可設定，自動上限報警功能。

★具有RS232數據接口，歷史數據可存儲6個月。

★離線檢測和在線檢測可選配。

★具有打印功能

測定原理：儀器采用紫外氧化的原理，將水溶液中的總有機碳氧化為二氧化碳，并且測定其含量，二氧化碳的測試采用的是直接電導率法，通過測試經過氧化反應的水溶液總碳含量和未經過氧化反應的樣品總無機碳的含量差值來測定總有機碳含量，即：總有機碳（TOC）=總碳（TC）-總無機碳（TIC）。

產品特點

1.儀器采用便攜設計，使用輕便，方便移動至取樣點。

2.采用嵌入式系統，觸摸屏設計，純中文操作方便簡易。

3.針對制藥用水（TOC含量在1000ppb以下）總有機碳含量的檢測設計，進行檢測。

4.配備大量的儲存空間，能夠存儲大量的測試數據。

5.中文打印，輸出測試參數、測試結果。

6.在使用、貯存和更換過程中不需要?dú)怏w或試劑，無移動部件，減少維修和維護成本。

7.當測試樣品濃度超過規定限度，儀器能夠自動報警，并輸出控制信號。

8.符合國家2010版《中國藥典》規定的測試方案，可以提供IQ/OQ/PQ服務。

氧化反應器

儀器利用UV射線在二氧化鈦光催化劑的作用下將有機化合物氧化成二氧化碳，氧化反應器是一個UV燈外包螺旋形的石英管。UV燈發出185nm和254nm的光線，使水產生光分解。

H2O hν(185nm)（TiO2）? OH?  H?

羥基自由基（OH?）能完全把有機化合物氧化為二氧化碳。

有機物  OH?? CO2 H2O

UV燈的使用壽命為6個月，當更換時間到期時儀器將出現警告信息，提醒用戶更換UV燈。

主要技術參數

電   源：220V?22V

檢測極限：0.001mg/L

檢測精度：?5%

檢測范圍：0.001mg/L～1.000mg/L

分析時間：4min

響應時間：15 min以內

樣品溫度：1-95℃

額定功率：100W

基本尺寸：44cm?18cm?26cm

相對濕度：≤ 85%

重復性誤差：≤ 3%

環境溫度：10-40℃    溫度變化在?5℃/d以內

內部樣品流速：0.5 ml/min

零點漂移：?5%

量程漂移：?5%

電源頻率：50Hz?1Hz

設備安裝調試：

免費為用戶提供所購儀器的安裝調試服務。在進行安裝調試前用戶方應提供相應的準備工作，并予以提前通知，具體安裝調試日期雙方可以協商而定。設備安裝調試由多年行業資深工程師免費進行。保證用戶可以正確使用、軟件操作和一般維護以及應及故障的處理。

Carbon dioxide sensor

There are two carbon dioxide sensors installed on the instrument, consisting of conductivity sensors and temperature sensors. The conductivity measurement adopts dual precision technology, which can achieve automatic calibration and temperature compensation. TIC sensors are used to detect the concentration of carbon dioxide in unoxidized water samples, while also detecting the conductivity value of the water samples; The TC sensor is used to detect the total concentration of carbon dioxide contained in the water sample itself and the carbon dioxide produced by the decomposition of organic matter in the water sample.

Diverter

After entering the instrument, the water sample is divided into two paths with the same flow rate. One path enters the carbon dioxide sensor through a delay coil to detect TIC, while the other path decomposes organic matter into carbon dioxide through the photocatalytic oxidation of titanium dioxide film using a UV lamp in an oxidation reactor, and enters the carbon dioxide sensor to detect TC. The total organic carbon can be calculated by this difference: TOC=TC–TIC.

Replace the peristaltic pump tube

The peristaltic pump tube may experience wear and aging after long-term operation, so it must be replaced regularly.

The operation steps for replacing the pump tube are as follows:

Turn off the main power switch and unplug the power cord.

Press the metal spring at the bottom of the pump head and pop out two plastic cards.

○3 Remove the old peristaltic pipe from the joint of the pipe, remove the clamp on the pipe, and place the clamp on the new one

On the peristaltic pump tube, then install the new tube into the joint of the instrument, paying attention to the position and direction of the clamp.

Insert two plastic cards and then press them down into the slots. Be sure to pay attention when pressing, regardless of whether it is pressed or not

Enter the slot.

Adjust the flow rate adjustment key on the card, and pay attention to the principle of adjustment: the liquid at the outlet of the pipeline should be smooth and self regulating

However, there is no reflux. If conditions permit, please use a high-precision measuring cylinder to measure the liquid flow rate and ensure the flow of the liquid

The speed corresponds to the flow rate setting of the instrument.

If there are any problems when replacing the above components, please contact the instrument manufacturer for resolution.

Save History

The objects for saving historical records include online analysis results and offline analysis results.

The analyzer has two storage modes, one is automatic storage; Another method is manual storage. When selecting automatic

When storing, the instrument will automatically save the test results after each test is completed. When selecting manual storage, every

At the beginning of the next test, the instrument will display a prompt message asking the user if they want to save the data. If you want to save the test

Press the "OK" button to save the test results. If you do not want to save, press the "Cancel" button to discard the save.

Main features:

★High precision, high sensitivity, and simple operation.

★Humanized operation interface, with one click operation function and automatic pipeline cleaning function.

★High performance CPU, touch screen design, large 640 * 480 dot matrix true color display.

★No need to open the chassis to replace the UV lamp and pump tube.

★The detection upper limit can be set, with automatic upper limit alarm function.

★Equipped with RS232 data interface, historical data can be stored for 6 months.

★Offline detection and online detection are optional.

★With printing function

Measurement principle: The instrument adopts the principle of ultraviolet oxidation to oxidize the total organic carbon in the aqueous solution to carbon dioxide and determine its content. The carbon dioxide test uses the direct conductivity method, which determines the total organic carbon content by measuring the difference between the total carbon content of the oxidized aqueous solution and the total inorganic carbon content of the unoxidized sample. That is, total organic carbon (TOC)=total carbon (TC) - total inorganic carbon (TIC).

Product features

1. The instrument adopts a portable design, which is lightweight and easy to move to the sampling point.

2. Adopting embedded system and touch screen design, pure Chinese operation is convenient and simple.

3. Design and conduct testing for the total organic carbon content of pharmaceutical water (TOC content below 1000ppb).

4. Equipped with a large amount of storage space, capable of storing a large amount of test data.

5. Print in Chinese, output test parameters and test results.

6. No gas or reagents are required during use, storage, and replacement, and there are no moving parts, reducing repair and maintenance costs.

When the concentration of the test sample exceeds the specified limit, the instrument can automatically alarm and output a control signal.

8. According to the testing plan specified in the 2010 edition of the Chinese Pharmacopoeia, IQ/OQ/PQ services can be provided.

Oxidation reactor

The instrument uses UV rays to oxidize organic compounds into carbon dioxide under the action of titanium dioxide photocatalyst. The oxidation reactor is a spiral shaped quartz tube wrapped around a UV lamp. UV lamps emit light at 185nm and 254nm, causing aquatic products to undergo photodegradation.

H2O hν(185nm) (TiO2) OH? H?

Hydroxyl radicals (OH?) can completely oxidize organic compounds into carbon dioxide.

Organic matter OH?CO2 H2O

The service life of UV lamps is 6 months. When the replacement time expires, the instrument will display a warning message to remind users to replace the UV lamp.

Main technical parameters

Power supply: 220V?22V

Detection limit: 0.001mg/L

Detection accuracy:?5%

Detection range: 0.001mg/L~1.000mg/L

Analysis time: 4 minutes

Response time: Within 15 minutes

Sample temperature: 1-95℃

Rated power: 100W

Basic size: 44cm?18cm?26cm

Relative humidity:≤85%

Repeatability error:≤3%

Environmental temperature: 10-40℃Temperature variation within?5℃/d

Internal sample flow rate: 0.5 ml/min

Zero drift:?5%

Range drift:?5%

Power frequency: 50Hz?1Hz

Equipment installation and debugging:

Provide users with free installation and debugging services for the purchased instruments. Before installation and debugging, the user should provide corresponding preparation work and give advance notice. The specific installation and debugging date can be negotiated by both parties. The equipment installation and debugging are carried out free of charge by experienced engineers in the industry for many years. Ensure that users can use the software correctly, perform software operations and general maintenance, and handle malfunctions promptly.