一、產品用途：
300型電動自動行走銑刨機是一款專門適用于混凝土地面多功能表面處理的路面機械，廣泛實用于橋面鋪裝，橋面拉毛，錯臺調平、舊路面

刨除，以及機場跑道、城市廣場、大型工廠，物流倉儲、車庫、停車場等混凝土地面施工、作業中。
Model 300 electric automatic walking milling machine is a special road surface machine which is suitable for multi-

functional surface treatment of concrete ground. It is widely used in bridge deck pavement, bridge deck stretching, 

stagger table leveling, old road surface planing, and Airport runways, city squares, large-scale factories, logistics 

storage, garages, parking lots and other concrete ground construction, operations.?
二、產品參數
型號ZXB300
主電機11kw/380v
自行電機1.5kw
一次銑刨寬度300mm
一次銑刨深度(混凝土)5-20mm
一次銑刨深度（瀝青）5-30mm
工作速度4m/min
外形尺寸1380?730?1180mm
整機重量306kg
三、技術指標
1. 發動機功率。功率越大，銑刨效果越好。
2. 刀軸數量和刀片數量。數量越多銑刨深度和效率越高。
3. 機器自重。越重越好，可以避免機器跳動。
4. 刀片齒數越多銑刨效果越好，臂如8齒刀片優于6齒刀片。
四、保養指南
1、為了安全起見，在進行保養前，所有的保養必須由合格的機修工來進行。
2、機器必須放在平整的平面上進行保養。檢查銑刀時要防止機器翻倒。
3、每次操作前用肉眼檢查機器：所有緊固件是否擰緊？是否有零件明顯磨損或開裂？檢查軸承、檢查個個防護罩是否蓋住，注意軸承加油

，本機軸承不能缺油。
4、每次操作前，要檢查皮帶松緊度。新皮帶在運轉4小時后應該重新調整松緊度。有斷痕、嚴重磨損的皮帶應立即調換新的。調整皮帶松

緊度：調整發動機安裝底板下的兩根高度調整螺柱，通過改變電機輸出軸和銑鼓中心軸的中心距離來控制皮帶的松緊度。必須保持適當?shù)?br />
皮帶松緊度。
5、每次改變銑刀排列時，檢查銑刀軸和軸襯。如果軸上出現磨損的槽，就需要換新的。

Technical Indicators 1. Engine power. The greater the power, the better the milling effect. 2. Number of tool shafts and 

number of blades. The greater the number, the greater the depth and efficiency of milling. 3. Machine weight. The heavier 

the better, to keep the machine from beating. 4. The more the number of teeth of the blade, the better the milling 

effect, such as 8-tooth blade is better than 6-tooth blade. Maintenance Guide 1. For safety reasons, all maintenance must 

be performed by a qualified mechanic before maintenance is performed. The machine must be maintained on a flat surface. 

The milling cutter must be checked to prevent the machine from tipping over. 3. Visually inspect the machine before each 

operation: Are All fasteners tightened? Are any parts visibly worn or cracked? Check the bearings, check whether the 

guard cover, pay attention to the bearing oil, the machine bearing can not be short of oil. Check the tightness of the 

belt before each operation. The new belt should be re-tightened after four hours of operation. The belt with broken marks 

and serious wear should be replaced immediately. ADJUST THE BELT TIGHTNESS: adjust the two height adjustment studs under 

the engine mounting base plate, control the belt tightness by changing the central distance between the motor output 

shaft and the milling drum central shaft. Proper belt tightness must be maintained. 5. Every time you change the cutter 

arrangement, check the cutter shaft and bushing. If a worn groove appears on the shaft, a new one is needed.
聯系人：陳經理
地址：山東省濟寧市任城區金宇路4號
手機：13165175381